posted on 2019-10-08 14:21:08
Now we have successfully updated A paper to PET film, instead of white paper.
1.The A paper is the matte surface of the film, the B paper is still the same as before.
2.When printing pictures, please apply PS, CDR, AI and other drawing software exported vector graphics, select OKI printer printing, and mirrorprinting. If the pattern contains white parts, the printing must select white toner.
3.The heat press machine temperature and time are set to 175 ° C, 90 S, and heavy pressure.
4.Cut the AB paper to the appropriate size for the pattern. B paper is slightly smaller than A paper. Place A paper on the silicone mat with the pattern side facing up. B paper is covered on the A paper. Place a blank part in the middle of the AB paper. 1cm wide paper strip, covered with high temperature oil paper, complete transfer
Pay attention to the following points in this step:
First, you can place a 1-2mm thick soft silicone on the B paper to increase the airtightness between the AB papers and improve the transfer effect. At this time, the pressure of the heat press machine is moderate.
Second, if there is no soft silicone, the pressure of the heat press machine needs to be adjusted to be particularly large, and it is very difficult to press the heat press machine.
Third, could use a small piece of copy paper between A and B paper when tearing B off A paper. It is convenient for your tearing.
5.Transfer operation:
Step 1: transfer B to A, press the time after the alarm time, raise the handle of the handle, bring the high temperature gloves with both hands to smooth the B paper, and evenly and continuously remove the paper strip and B paper (grey back label). Hot tearing (the film must not leave the silicone pad at the bottom of the device, press down the hand and peel off the B paper at a constant speed). When tearing off the B paper, the smaller the angle between the B paper and the A paper, the better.
Step 2: Check A paper film, whether there is a white rubber mark on the edge of the transferred pattern, and if necessary, cut off the white part.
The third step: transfer the A film image onto the cloth: the time is adjusted to 20 seconds, the temperature and pressure are unchanged; the cloth or clothes are tiled on the ironing board, and the film pattern is transferred face down (the excess glue marks on the edge are cut, Cover the 2mm thick silicone pad to make the pattern fit closely to the fabric); press the machine handle after pressing the alarm time, then tear it when the fabric is completely cooled, that is, cold tear, pick up a corner of the film, gently roll and tear off, (film The smaller the angle of peeling off from the cloth, the more perfect the transfer effect), the tearing off the film to complete the transfer; the cover paper can be covered for 3-5 seconds to enhance the firmness.
6.washing and maintenance: printing after 24 hours of washing, hand washing machine can be. Do not dry and soak for a long time while washing. Do not directly stretch the pattern and use bleach.
Notes:
- Depending on the heat press machine, the temperature time is slightly different. It is recommended to use the sample for testing before transferring the paper.
- It is recommended that customers buy a 1-2MM silicone pad. When transferring, the pressure of the heat press machine can be reduced appropriately.
- B paper is transferred to A paper. This step is very important. If this operation is unsuccessful, the subsequent operation will not be successful. Before tearing off B paper, be sure to flatten the flat paper. When tearing off B paper, be sure to Evenly hot tearing, A paper film can not leave the hot drawing board, tearing off the angle between the B paper and the A paper is as small as possible
- The second step is to tear off the A paper film. It is necessary to tear off the A paper after the fabric is completely cooled. When the A paper is torn off, it needs to be carried out slowly (especially some very fine lines), A paper and cloth clips. The smaller the corner, the better
- Dark hollow paper is recommended for use on low-elastic, micro-elastic or non-smooth cotton fabrics.
Website:www.itransferpaper.com
Email:vision@itransferpaper.com
Whatsapp:+86-17321388330
Facebook:https://www.facebook.com/itransferpaper/
Twitter:http://twitter.com/itransferpaper
Youtube:https://www.youtube.com/channel/UC8W_0PRzeWjOhba9WZaH2xw
Google+:https://plus.google.com/u/0/+VISIONsublimationpaper
Linkedin:https://www.linkedin.com/in/itransferpaper/
